Be Prepared for OSHA’s COVID-19 Special Emphasis Program (SEP) Enforcement!

April 5, 2021

The new administration is putting a lot of pressure on OSHA to perform COVID-19 related inspections and enforce the agency’s guidance to prevent the spread of COVID-19 in the workplace. OSHA’s new Special Emphasis Program (SEP) on COVID-19 gives the agency the impetus it needs to do just that. Employers should prepare for the possibility of unprogrammed and programmed COVID-19 inspections.

Unprogrammed Inspections:

To start, make sure you know your rights as an employer, so that you will not unnecessarily provide OSHA with information that could result in a citation. Unprogrammed inspections typically result from the mandatory reporting of a fatality, an employee complaint, or a referral from another government agency. When an inspection is unprogrammed you can limit the scope of the compliance officer’s inspection to the reason for the unprogrammed inspection. For example, if an employee complains to OSHA that the portable toilets are not being regularly sanitized, and that complaint results in an unprogrammed inspection, you can limit OSHA to inspecting only those toilets and prevent the compliance officer from seeing other areas of the jobsite. However, compliance officers can issue citations for safety violations they identify while on the way to inspect the subjects of unprogrammed inspection, so choose the path and mode of transportation to that subject area wisely.  

  • Compliance officers are required to hold pre-inspection conferences. Make sure the conference occurs. There have been cases where compliance officers have omitted this required step in the process;
  • Make sure your company is represented at the conference by someone who knows what to ask and understands how to respond;   
  • The instant the conference begins your company representative should ask the compliance officer for the reason for the inspection;
  • If it is an unprogrammed inspection, limit the compliance officer to the area of the jobsite where the incident that resulted in the inspection occurred, i.e., where the fatality occurred, the specific area of the employee complaint, or the specific area stated in the referral; and  
  • Never leave a compliance officer alone to wander the jobsite. Even though it is an unprogrammed inspection, if a compliance officer sees a violation, he or she can still issue a citation that is unrelated to the reason for the unprogrammed inspection.

Programmed Inspections:

Programmed inspections are randomly selected by OSHA from Dodge Reports. Get  prepared ahead of time in case your company is working on a project that comes up for a programmed COVID-19 inspection. To get prepared, consider what the compliance officers are most likely to look for during the inspection process, and what standards that they are most likely to cite.

Based on OSHA’s most recent COVID-19 compliance directive its compliance officers will be looking specifically for the following items during COVID-19 inspections:

  • Evidence of retaliation against workers for actions related to the virus;
  • Use of face coverings or masks throughout the workplace;
  • Active encouragement of workers to stay home if they are sick;
  • Proper social distancing and accommodating workers with telework where possible;
  • Emphasis on proper respiratory etiquette;
  • Emphasis on proper hand hygiene;
  • Routine environmental cleaning; and
  • Planning for possible infectious disease outbreaks in the workplace.

Since OSHA does not currently have a COVID-19 standard, the agency uses existing standards to enforce worker COVID-19 protection. When performing COVID-19 inspections the agency is most likely to issues citations from provisions in the following standards and its general duty clause.

Mechanical Service and Fabrication Shops:

  • 29 CFR 1904 – Recording and Reporting Occupational Injuries and Illnesses;
  • 29 CFR 1910.132 – General Requirements – Personal Protective Equipment;
  • 29 CFR 1910.134 – Respiratory Protection;
  • 29 CFR 1910.141 – Sanitation;
  • 29 CFR 1910.145 – Specification for Accident Prevention Signs and Tags;
  • 29 CFR 1910.1020 – Access to Employee Exposure and Medical Records;
  • 29 CFR 1910.1030 – Bloodborne Pathogens; and
  • Section 5(a)(1) – General Duty Clause – From the OSH Act of 1970.

Mechanical Construction:

  • 29 CFR 1904 – Recording and Reporting Occupational Injuries and Illnesses;
  • 29 CFR 1926.28 – General Requirements – Personal Protective Equipment;
  • 29 CFR 1926.33 – Access to Employee Exposure and Medical Records;
  • 29 CFR 1926.51 – Sanitation;
  • 29 CFR 1926.103 – Respiratory Protection;
  • 29 CFR 1926.200 – Accident Prevention Signs and Tags; and
  • Section 5(a)(1) – General Duty Clause from the OSH Act of 1970.

If you have any questions or need any assistance protecting your workers from COVID-19 orpreparing your company for possible OSHA COVID-19 related enforcement, please contact Pete Chaney at pchaney@mcaa.org or 301-990-2214.

Related Articles
OSHA recently updated their guidelines on mitigating and preventing the spread of COVID-19 in the workplace, which reflects the July 27, 2021 Centers for Disease Control and Prevention (CDC) mask and testing recommendations for fully vaccinated people.…
Each week, MCAA will highlight one or more of the educational resources that are free to MCAA members as a benefit of membership. This week, we focus on MCAA’s new safety training video, Master the Mechanics: Hand & Power Tool Safety for the Mechanical Trades. The video provides trainees with information on the most common hand and power tool injuries in the mechanical construction and service trades. It highlights the tools most likely to be involved in an injury incident, and teaches proper use of the tools to help prevent injuries.…
MCAA extends a warm welcome to Raffi Elchemmas, who will be joining the staff starting August 2, 2021. He will be MCAA’s new Executive Director of Safety, Health and Risk Management, learning the ropes before Pete's upcoming retirement. Raffi comes to us from Milwaukee Tool, where he was the National Manager, Health & Safety. He is a board-certified ergonomist with an MBA in Sales Leadership & Health Sector Management from DePaul University. He has been a member of MCAA’s Safety and Health Committee since 2019. MCAA is pleased to welcome Raffi to the staff, and his wife Martha, daughter Nina, and son Vartan to the MCAA staff family.…
STIHL is recalling to repair certain TS 410 and TS 420 cut-off machines manufactured between January 2021 and April 2021. In some of these machines the flywheel can break apart while the engine is running, posing a projectile hazard to the users or bystanders. If you have any of these machines, immediately discontinue use and take them to an authorized STIHL dealer for free repair. …
Load More...